20:22:43 EST Thu 19 Nov 2026
Enter Symbol
or Name
USA
CA



Silver Bullet Mines Corp
Symbol SBMI
Shares Issued 148,907,895
Close 2026-11-19 C$ 0.09
Market Cap C$ 13,401,711
Recent Sedar+ Documents

Silver Bullet's Gold Queen stockpiles average 17 g/t Au

2026-11-19 19:41 ET - News Release

Mr. John Carter reports

SILVER BULLET MINES CORP. BEGINS WORK ON FIRST 200 TONS OF DSO FOR SHIPMENT

Silver Bullet Mines Corp. is updating shareholders on the company's near-term path to production of higher-grade saleable concentrate and direct ship ore. Supporting this path are the recent assay results from samples from Gold Queen stockpiles, which assay results average over 17 grams of gold per ton.

The Columbia/Gold Queen complex is composed of the past-producing Columbia mine, the past-producing Gold Queen mine, the past-producing Steamboat mine, at least four other newly discovered potential high-grade gold zones and large stockpiles from the Gold Queen built by unknown parties.

The company's goal is near-term production with near-term revenue. There are two parts of the plan to reach this goal.

Part of the plan to reach this goal was to test the mineralization in some of the remaining stockpiles. With a sufficient grade of gold and silver mineralization, Silver Bullet would load tonnage from the stockpiles, truck it to the company's mill roughly 30 miles away and process it into saleable concentrate.

The other part of the plan was to advance revenue opportunities from direct ship ore. To that end, the company has begun processing mineralized material from some of the Gold Queen stockpiles. This material will be processed at the company's mill, going only through the fine ore crusher and coarse ore crusher, but not through the ball mill, which should reduce the cost to the company and reduce the time to process the material.

This material for DSO is currently being crushed to less than one-half inch as per client's requirement. The first minimum order should be for 200 tons of DSO. Currently, 40 tons have been processed and are ready for bagging. Further tonnage from stockpiles is on the ground at the mill awaiting processing, and additional stockpile tonnage is being readied for shipment to the mill.

Recent in-house assay results from samples taken from near the past-producing Gold Queen mine, Stockpile 1, Stockpile 2 and the mill stockpile are below. These strong assay results support the company's near-term path to production.

Other samples from the Gold Queen stockpiles have been sent to a third party accredited lab for multielement testing.

The company does not yet have enough data to advise on what the concentration ratio could be once the mineralized material from the stockpiles is regularly processed through the company's mill into either concentrate or DSO, nor can the company yet advise on what weekly tonnage through the mill will be for either concentrate or DSO.

Qualified person

Robert G. Komarechka, PGeo, an independent consultant, has reviewed, verified and approved Silver Bullet's work referred to herein and is the qualified person for this release as per the exchange requirements and National Instrument 43-101. Note: The QP was not at the site for sample collection.

Quality assurance/quality control from Silver Bullet lab in Globe, Ariz.

Samples are random by nature, and may not be representative of a particular Gold Queen stockpile or any or all of them. All samples were collected randomly by Silver Bullet's team on site. The mill stockpile sample was collected by taking a shovel load at each four-foot interval around the perimeter of the stockpile, which shovel loads were then combined and split for assaying. The samples from the stockpiles were analyzed by Silver Bullet at its in-house facility near Globe, Ariz. These samples were processed through the lab jaw crusher, lab hammer mill and splitter box into an aliquot. Most of the pulverized aliquot was mixed with a flux and flour combination and melted in a crucible at 1,850 F, with the rest being logged and archived. Upon cooling, the poured melt was in the form of a metal button and slag, following which a bone ash cupel was utilized to eliminate the lead in the button to form a bead. The bead was then weighed, following which a solution of six to one distilled water to nitric acid was utilized to dissolve the gold in the bead at approximately 175 F.

We seek Safe Harbor.

© 2026 Canjex Publishing Ltd. All rights reserved.